Installing satalite dishes

The satellite that your dish connects with is in a geosynchronous orbit moving the same as the earth somewhere above the equator.

This means if you reside in North America, your satellite dish needs a clear and unobstructed view of the southern sky to pick up signals from that satellite.

Your position relative to the satellite determines the required vertical and horizontal alignment for the dish, which you can measure with a signal meter. Your dish also needs a cabled connection to the satellite receiver and your television. In addition to positioning and cabling, your dish needs a mounting surface that is stable and secure. Nothing should block the satellite signal. Even branches and leaves will interfere and cause reception problems.

I used another dish to configure the receiver. After connected the coaxial cable from your dish to the LNB, then proceed to use blindscan to get all the channels on the position point your dish. Great day to you, please I try setting strong dish, but at the end, all the channels that shows are non Nigeria channel, what should I do and what is the location for strong decoder.

Free to air. What is the right size of dish to be use for startime signal tracking, and to which direction; west or east position!? Good day everyone. Please I need somebody to explain it to me. Please am in Ghana, I need all the symbol rates, transponders, poralities and frequencies of StarTimes in Ghana now. I appreciate your kind consideration. Thank you. I have track star time network using frequency and symbol rate And the decoder is not getting any Chanel using auto search.

What can I do? Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. You must use a coaxial cable of satellite quality, somewhat thicker than the one used inside, with its corresponding connectors. In the cable sheath you will find information about its uses. The satellite receiver It is the device that transforms the signal received by the antenna so that it can be seen on televisions. It is the point at which the coaxial cable arrives from the satellite dish, and from which the cable that goes to the TV comes out.

It is best to make this connection with HDMI, so that there is no loss of sharpness in the image. In addition, with a cable or wireless connection you can receive Internet services that are contracted with the telephone company. Does your building have a home automation network and do you want to install a satellite dish?

The installation wiring can be used to channel the antenna cable to your home if they give you the corresponding authorization. In a single-family home, you will only have to attend to the possible urban norms. Once each part of the kit has been identified, it is time to mount the parabolic and then install it at the appropriate point. In general, the steps are as follows:.

Step 1. Fix the anchor legs of the support to the back of the plate: normally it is placed with four through screws and four nuts. Do it with their corresponding screws and nuts. Tighten the screw with a flat wrench. Put the LNB, but do not tighten at all until regular. Before installing the satellite dish on the wall of any common element of a community of neighbors, you must inform yourself if it has specific rules for its placement.

Normally it only affects aesthetics, but in some cases in historical buildings, for example the regulations may be stricter. You should also inform yourself before placing it on the street, in case the city council imposed conditions. The final step when installing an Antenna is to put it in place.

The process is as follows:. Step 2. With a bubble level, place the bracket on the wall to mark the anchor points. It is important that the support is well fixed so that it resists strong winds. Place the plugs flush with the wall, then fix the support and put the screws, in this case hexagonal head. Approach the plate with the arm of the structure already mounted before the support tube or mast. Fasten with the jaw or screw. At the same time screw the two nuts to achieve a homogeneous adjustment in both parts.

You should place it approximately, both in height and in line with respect to the point of the satellite you wish to tune. Follow the recommended parameters. Tighten the jaw or U-bolt with a flat wrench if not included in the kit, you will have to buy it until the antenna arm is secured.

The circular support serves to regulate the azimuth of the antenna. After installing a satellite dish, there is still an essential step: connect it to the receiver or socket to access the satellite contents. Learn how to do it right:. Step 3.