Install sub amp diagram

A a great but affordable amp wiring kit like this Belva 8-gauge complete kit includes not just the basics but a lot more. My advice is to pick up a good amp wiring kit and the tools you need beforehand. Need advice on finding the right installation wiring?

Check out my post with some of the best wiring kits for the money here. Thank you for taking the time to post this. I have always been confused about so much of this you covered. I have a full understanding now!

Much appreciated. Is there a possible way to connect front speakers to high level input and a sub woofer to a RCA input? Please help! You would be better off just using a line level converter if you really need RCA connections. I have a 4 channel watt amp. That can be bridge and run any ohm. I have 2 component speakers 4 ohm with crossover and tweeters. And 2 subs 4 ohm dvc. Can I wire this to this amp.? In parallel? At any rate, you can either use one DVC sub wired for 2 ohms, one per channel, or bridge the rear channels and wire both subs in series.

Read on to find out how! There are plenty of detailed diagrams to guide you, too. Contents What you need to know first What does the minimum impedance Ohms rating mean for an amp? Why is this best for driving a subwoofer? Diagram — How to wire a 4 channel amp to 4 speakers and a sub Using power resistors for harder installations 4 ohm min. How to connect a 2 ch.

Connect the other cables as stated in your instruction manual for the audio system. You probably need to use RCA cables to connect the head unit to the line out converter. You may need to plug a cable into the output port on the head unit and run it into the input port on the line out converter. Run the blue cable to the amp on the opposite side of the vehicle. Your line out converter comes with a blue connection cable.

This cable relays information from your line out converter to your amplifier. Leave the blue cord next to the red power cord. Method 3.

Either find an unpainted, metal surface in your vehicle and mount the grounding loop to the metal or rip up a piece of fabric in an inconspicuous area to expose the metal underneath. You cannot attach the wire to a painted surface. Use sandpaper to remove paint from a small section of metal if you need to. Connect your line out converter to the amplifier. Set your amplifier down near the area where it is grounded to the chassis. Sometimes, all 3 of these cables are bundled together.

Connect the power cord to the opposite side of the amplifier. Hook up the red power cable from the battery to the amplifier. If the open end of your power cable is a loop and the opening for your power cable is a slot, use wire cutters to strip the end of the cable and expose a 0.

Slide it into the opening and press down on the latch to close the connection. Then, tighten the cap over the loop to set it in place. Connect the subwoofer RCA cables to the amplifier. Connect the left channel on the subwoofer to the left channel on the amplifier and the right channel on the subwoofer to the right channel on the amplifier. If there is a separate power cord for the sub, you may need to attach this to the amp as well. Reconnect your battery and test the system. Before you reassemble your dashboard, reconnect the negative battery terminal.

Turn your volume knob all the way down and then start your vehicle. Try playing some music. Slowly turn the volume up. If you hear your music, go ahead and turn the vehicle off before reinstalling the dashboard using the same clips and parts. If the audio sounds distorted, check your line out converter to make sure that your connections are clean. The wires are not grounded properly, check to make sure the surface is clean, unpainted metal.

Not Helpful 7 Helpful I have a Pioneer deck, amp, and kicker, installed to shut off from the battery. The sub cuts on and off at high volume when I use the auxiliary cord to phone. How do I fix this? That could mean your amp cannot handle the sub. Another important factor to consider is Ohms. If you have a 2 ohm sub and a 4 ohm amp it won't produce enough power to properly power the sub.

Not Helpful 3 Helpful Not Helpful 6 Helpful You should be able to connect it to the auxiliary on the back of the stereo unit. Not Helpful 3 Helpful 9. What would cause my sub to kick in when radio is on and stop working when I change source to CD? The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna.

Remove the wire and find the correct remote amp, then turn on wire or ignition wire to the vehicle. Not Helpful 16 Helpful I cannot turn it up any higher than halfway without my amp going into protective mode. What would cause this? This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 3 Helpful 4. What if I bought my radio harness to fit my truck only?

Will the wires still match up on the aftermarket radio I purchased? Yes, you can. It will just plug into your truck and then connect color coordinated wires. Not Helpful 1 Helpful 4.

My amp is already installed and I just bought a new sub. How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps.

Just match the positive and negatives. A pictorial diagram would operate more detail of the visceral appearance, whereas a wiring diagram uses a more figurative notation to highlight interconnections more than mammal appearance. A wiring diagram is often used to troubleshoot problems and to make determined that all the connections have been made and that anything is present.

Architectural wiring diagrams play the approximate locations and interconnections of receptacles, lighting, and unshakable electrical facilities in a building.

Interconnecting wire routes may be shown approximately, where particular receptacles or fixtures must be on a common circuit.